CTRON-CDP-MIB

CTRON-CDP-MIB DEFINITIONS ::= BEGIN

--    ctron-cdp-mib.txt
--        Revision: 1.00.04
--        Part Number:
--        Date: August 28, 1999

--    Cabletron Systems reserves the right to make changes in
--    specification and other information contained in this document
--    without prior notice.  The reader should consult Cabletron Systems
--    to determine whether any such changes have been made.
--
--    In no event shall Cabletron Systems be liable for any incidental,
--    indirect, special, or consequential damages whatsoever (including
--    but not limited to lost profits) arising out of or related to this
--    document or the information contained in it, even if Cabletron
--    Systems has been advised of, known, or should have known, the
--    possibility of such damages.
--
--    Cabletron grants vendors, end-users, and other interested parties
--    a non-exclusive license to use this Specification in connection
--    with the management of Cabletron products.
--
--    Copyright September 1999 Cabletron Systems
--

IMPORTS
       ctCDP
                FROM CTRON-MIB-NAMES
       ifIndex, InterfaceIndex
                FROM IF-MIB 
       MODULE-IDENTITY, OBJECT-TYPE, IpAddress, Counter32
                FROM SNMPv2-SMI
       MODULE-COMPLIANCE, OBJECT-GROUP
                  FROM SNMPv2-CONF
        MacAddress, TimeStamp, TEXTUAL-CONVENTION, DisplayString
                FROM SNMPv2-TC
        TimeFilter
                FROM RMON2-MIB;

ctronCdpMIB MODULE-IDENTITY 
   LAST-UPDATED
     "199908280000Z"  -- August 28, 1999 

   ORGANIZATION
     "Cabletron Systems, Inc."

   CONTACT-INFO
    "Cabletron Systems, Inc.
     35 Industrial Way, P.O. Box 5005
     Rochester, NH 03867-0505
     (603) 332-9400
     support@ctron.com
     http://www.ctron.com"

   DESCRIPTION
     "This module defines a schema that maintains per port
      neighbor information for the express purpose
      of helping a managment application map 
      Layaer 2 topology."
    ::= { ctCDP 3 }   


   CTCDPCapability ::= TEXTUAL-CONVENTION
   STATUS current          
   DESCRIPTION 
            "The current capabilities of the neighbor device on a per
port basis.  "
   SYNTAX INTEGER {
                igmp(1),      -- IGMP enabled on the port over which device sent the packet 
                rip(2),       -- Device performs routing using RIP
                bgp(3),       -- Device performs routing using BGP
                ospf(4),      -- Device performs routing using OSPF
                dvmrp(5),     -- Device performs DVMRP routing
                ieee8021q(6), -- Device supports 802.1Q packet format on the port over
                              -- which it sent bthe CDP packet
                gvrp(7),      -- Device supports GARP VLAN Registration Protocol
                gmrp(8),      -- Device supports Multicast Registration Protocol
                igmpSnoop(9),       -- Device is a bridge and supports IGMP protocol snooping
                dhcpServer(10),     -- Device runs DHCP Server
                dnsServer(11),      -- Device runs DNS Server
                activeDirectory(12) -- Device runs Active Directory Server
   }

ctCDPNeighbor   OBJECT IDENTIFIER ::= { ctCDP 1 }
ctCDPStatus     OBJECT IDENTIFIER ::= { ctCDP 2 }
ctCDPStats      OBJECT IDENTIFIER ::= { ctCDP 4 }

ctCDPNeighborLastChange OBJECT-TYPE
     SYNTAX      TimeStamp
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The value of sysUpTime at the time the cdpNeighborTable
         was subject to these events: row insertion, row deletion"
    ::= { ctCDPNeighbor 1 }

ctCDPNeighborLastDelete OBJECT-TYPE
     SYNTAX      TimeStamp
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The value of sysUpTime the last time an entry in the
        ctCDPNeighborTable was deleted. This should be polled 
        at an interval no greater than one second.
        When it changes, the whole table should be 
        reread by management with a timeMark of 0 to rebuild
        connectivity map."
    ::= { ctCDPNeighbor 2 }


ctCDPNeighborTable     OBJECT-TYPE
     SYNTAX  SEQUENCE OF CtCDPNeighborEntry
     MAX-ACCESS  not-accessible
     STATUS  current
     DESCRIPTION
        "The CommonNeighborTable holds all known neighbors speaking
         cdp protocols."
        ::= { ctCDPNeighbor 3 }

ctCDPNeighborEntry    OBJECT-TYPE
     SYNTAX      CtCDPNeighborEntry
     MAX-ACCESS  not-accessible
     STATUS  current
     DESCRIPTION
         "An entry containing objects pertaining to  
          neighbor devices speaking CDP protocols."
     INDEX   { ctCDPNeighborTimeMark, ifIndex, ctCDPNeighborMAC  }
        ::= { ctCDPNeighborTable 1 }

CtCDPNeighborEntry ::=
SEQUENCE {
           ctCDPNeighborTimeMark      TimeFilter,
           ctCDPNeighborMAC           MacAddress,
           ctCDPNeighborIP            IpAddress,
           ctCDPNeighborPort          InterfaceIndex,
           ctCDPNeighborType          INTEGER,
           ctCDPNeighborChassisMAC    MacAddress,
           ctCDPNeighborChassisIP     IpAddress,
           ctCDPNeighborDescription   DisplayString,
           ctCDPNeighborPortName      DisplayString,
           ctCDPNeighborCapability    CTCDPCapability
        }

ctCDPNeighborTimeMark OBJECT-TYPE
     SYNTAX      TimeFilter
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "A TimeFilter for this entry as defined in RFC 2021."
        ::= { ctCDPNeighborEntry 1 }

ctCDPNeighborMAC    OBJECT-TYPE
     SYNTAX      MacAddress
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The interface mac address of neighboring entity."
        ::= { ctCDPNeighborEntry 2 }

ctCDPNeighborIP    OBJECT-TYPE
     SYNTAX      IpAddress
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The IP address of SNMP agent on neighboring entity from which
         corresponding data for this port may be obtained. In the case
         of unnumbered IP Interfaces, this may not be the same as the 
         port."
        ::= { ctCDPNeighborEntry 3 }

ctCDPNeighborPort OBJECT-TYPE
     SYNTAX      InterfaceIndex
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The ifIndex of the remote port. Note, there may not be an IP 
         Interface associated with this port."
        ::= { ctCDPNeighborEntry 4 }

ctCDPNeighborType    OBJECT-TYPE
     SYNTAX  INTEGER {
                secureFastSwitch(1),
                dot1qSwitch(2),
                router(3),
                dot1dBridge(4),
                vlanManager(5),
                dnsServer(6),
                dhcpServer(7),
                dnsDhcpServer(8)
                }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The type of entity. This value is used to determine the
         general type of the object or service connected to a given port.
         In general, it is better to use system group sysServices to
         obtain an object's functionality."
        ::= { ctCDPNeighborEntry 5 }

ctCDPNeighborChassisMAC    OBJECT-TYPE
     SYNTAX      MacAddress
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The MAC Address of the chassis in architectures
         where many manageable  elements exist within a 
         given chassis. If no containing chassis exists, 
         exists, this value must be set to 000000:000000"
        ::= { ctCDPNeighborEntry 6 }

ctCDPNeighborChassisIP    OBJECT-TYPE
     SYNTAX      IpAddress
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The IP address of the chassis itself. If no containing chassis
         exists, this value must be set to 0.0.0.0"
        ::= { ctCDPNeighborEntry 7 }

ctCDPNeighborDescription  OBJECT-TYPE
     SYNTAX      DisplayString
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "A textual description of the neighbor. It
         should contain operator diagnostic information 
         similar to sysDescr: system type, firmware version..."
        ::= { ctCDPNeighborEntry 8 }

ctCDPNeighborPortName   OBJECT-TYPE
     SYNTAX      DisplayString
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The value of object ifName of the neighbor's port."
        ::= { ctCDPNeighborEntry 9 }

ctCDPNeighborCapability    OBJECT-TYPE
     SYNTAX      CTCDPCapability
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The current capabilities of the neighbor port."
        ::= { ctCDPNeighborEntry 10 }

--
--  CDPConfiguration Section
--

ctCDPGlobalStatus OBJECT-TYPE
     SYNTAX  INTEGER {
        enable(1),
        disable(2),
        autoEnable(3)
        }
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
        "The state of CDP for this entire managed entity. autoEnable(3)
         should the default mode for new implementations. In autoEnable
         mode, the device listens for CDP messages and upon receipt, begins
         sending CDP messages of the same version and type as received."
    ::= { ctCDPStatus 1 }

ctCDPAuthenticationCode OBJECT-TYPE
     SYNTAX      OCTET STRING (SIZE( 0..255))
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
        "The authentication code may be set to create individual CDP
        domains. CDP packets that arrive on a port must contain this
        string. This authentication code is global for the entire
        managed entity. The default for this string is 16 nulls."
   ::= { ctCDPStatus 2 }

ctCDPPortTable OBJECT-TYPE
     SYNTAX  SEQUENCE OF CtCDPPortTableEntry
     MAX-ACCESS  not-accessible
     STATUS  current
     DESCRIPTION
        "This table shows enable/disable CDP status for each port."
   ::= { ctCDPStatus 3 }

ctCDPPortTableEntry OBJECT-TYPE
     SYNTAX      CtCDPPortTableEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
        "Each entry is indicative of a particuliar port in the system."
    INDEX   { ctCDPPort }
   ::= { ctCDPPortTable 1 }

CtCDPPortTableEntry ::=
    SEQUENCE {
        ctCDPPort
            InterfaceIndex,
        ctCDPPortStatus
            INTEGER
        }

ctCDPPort OBJECT-TYPE
     SYNTAX      InterfaceIndex
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The ifIndex for a physical port. ifConnectorPresent is true(1) 
         defines a physical port on which cdp pdus will be emitted."
    ::= { ctCDPPortTableEntry 1 }

ctCDPPortStatus OBJECT-TYPE
     SYNTAX  INTEGER {
                enabled(1),   -- CDP is enabled always on the port
                disabled(2),  -- CDP is disabled always on the port
                autoEnable(3) -- CDP is automatically enabled on the port 
                              -- when device receives CDP packet on that port
        }
     MAX-ACCESS  read-write
     STATUS  current
     DESCRIPTION
        "The current state administrative of cdp on a physical port. 
         The ability to enable and disable the sending of CDP pdu's 
         on a per port basis is controlled here."
    ::= { ctCDPPortTableEntry 2 }


ctCDPTransmitFrequency OBJECT-TYPE
     SYNTAX      INTEGER (5..900)
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
        "The rate in seconds at which CDP pdu's are sent on all enabled ports."
   ::= { ctCDPStatus 4 }

ctCDPHoldTime OBJECT-TYPE
     SYNTAX      INTEGER (15..600)
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
        "The maximum amount of time in seconds to wait before aging out
         an entry in the ctCDPNeighborTable. The agent may choose to change
         this value based on the hold time it receives from other devices
         so as to have a stable neighbor table which ages out entries 
         in accordance with the transmit frequency."
   ::= { ctCDPStatus 5 }

ctCDPVersion OBJECT-TYPE
     SYNTAX      OCTET STRING (SIZE(2))
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
        "The CDP version supported by this device as a bit string.
         For example, given support for two versions of cdp: 3 and 4
         the bit representation in big endian form would be: 00001100."
   ::= { ctCDPStatus 6 }

--
-- CDP statistics
-- 

ctCDPInPackets OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION 
        "Count of CDP packets received by the device over all 
         the ports."
   ::= { ctCDPStats 1 }

ctCDPOutPackets OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION 
        "Count of CDP packets successfully transmitted by the 
         device over all the ports."
   ::= { ctCDPStats 2 }

ctCDPInvalidVersionPackets OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION 
        "Count of CDP packets received with version not 
         supported by the device."
   ::= { ctCDPStats 3 }

ctCDPParseErrorPackets OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION 
        "Count of CDP packets received and could not be parsed
         successfully by the device."
   ::= { ctCDPStats 4 }

ctCDPTransmitErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION 
        "Count of errors occured by the device while trying 
         to transmit CDP packets."
   ::= { ctCDPStats 5 }

ctCDPMemoryErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION 
        "Count of memory errors occured in the device while 
         either trying to process the CDP packet or adding the 
         neighbor entry or while trying to send a CDP packet."
   ::= { ctCDPStats 6 }


--
-- Compliance Statements 
--

ctCDPConformance OBJECT IDENTIFIER ::= { ctronCdpMIB 11 }
ctCDPCompliances OBJECT IDENTIFIER ::= { ctCDPConformance 1 }
ctCDPGroups OBJECT IDENTIFIER      ::= { ctCDPConformance 2 }
 
ctCDPComplianceV10 MODULE-COMPLIANCE
    STATUS current
    DESCRIPTION
            "The compliance statement for the ctronCdpMIB."
    MODULE  -- this module
        MANDATORY-GROUPS { ctCdpGroupV10 }
    ::= { ctCDPCompliances 1 }

ctCdpGroupV10  OBJECT-GROUP 
   OBJECTS {
    ctCDPNeighborLastChange,
    ctCDPNeighborLastDelete,
    ctCDPNeighborTimeMark,
    ctCDPNeighborMAC,
    ctCDPNeighborIP,
    ctCDPNeighborPort,
    ctCDPNeighborType,
    ctCDPNeighborChassisMAC,
    ctCDPNeighborChassisIP,
    ctCDPGlobalStatus,
    ctCDPAuthenticationCode,
    ctCDPPort,
    ctCDPPortStatus,
    ctCDPNeighborDescription,
    ctCDPNeighborPortName,
    ctCDPNeighborCapability,
    ctCDPTransmitFrequency,
    ctCDPHoldTime,
    ctCDPVersion,

    ctCDPInPackets,
    ctCDPOutPackets,
    ctCDPInvalidVersionPackets,
    ctCDPParseErrorPackets,
    ctCDPTransmitErrors,
    ctCDPMemoryErrors
 }
 STATUS current
 DESCRIPTION
  "The set of managed objects that make up version 2 of the
   CTRON-CDP-MIB."
   ::= { ctCDPGroups 1 } 

END