Meross MSG200

[evanbeek]

I have an MSG200 (non HK) with 2 garage doors (1 & 2). When I connect it and log in, it shows:

[12/30/2023, 10:44:08 AM] [Meross] Initializing Meross platform...
[12/30/2023, 10:44:08 AM] [Meross] Initializing child bridge 0E:85:85:ED:B3:AA
[12/30/2023, 10:44:08 AM] [Meross] Initialising plugin v10.2.8 | System darwin | Node v18.17.1 | HB v1.7.0 | HAPNodeJS v0.11.1...
[12/30/2023, 10:44:08 AM] [Meross] Plugin initialised. Setting up accessories....
[12/30/2023, 10:44:09 AM] [Meross] [Smart Garage Door Opener] has been added to Homebridge.
[12/30/2023, 10:44:09 AM] [Meross] [Smart Garage Door Opener] initialising with options {"connection":"hybrid","garageDoorOpeningTime":20}.
[12/30/2023, 10:44:09 AM] [Meross] [Large Garage Door] has been added to Homebridge.
[12/30/2023, 10:44:09 AM] [Meross] [Large Garage Door] initialising with options {"connection":"hybrid","garageDoorOpeningTime":20}.
[12/30/2023, 10:44:09 AM] [Meross] [Small Garage Door] has been added to Homebridge.
[12/30/2023, 10:44:09 AM] [Meross] [Small Garage Door] initialising with options {"connection":"hybrid","garageDoorOpeningTime":20}.
[12/30/2023, 10:44:09 AM] [Meross] [Smart Garage Door Opener] initialised with id [2209298533592961070348e1e9a9ae01}].

And then:

[12/30/2023, 10:44:14 AM] [Meross] [Smart Garage Door Opener] current target [closed].
[12/30/2023, 10:44:14 AM] [Meross] [Smart Garage Door Opener] current state [closed].
[12/30/2023, 10:44:14 AM] [Meross] [Large Garage Door] current target [closed].
[12/30/2023, 10:44:14 AM] [Meross] [Large Garage Door] current state [closed].
[12/30/2023, 10:44:14 AM] [Meross] [Smart Garage Door Opener] has been reported [online].
[12/30/2023, 10:44:14 AM] [Meross] [Smart Garage Door Opener] has been reported [online].
[12/30/2023, 10:44:14 AM] [Meross] [Large Garage Door] has been reported [online].
[12/30/2023, 10:44:14 AM] [Meross] [Small Garage Door] has been reported [online].

As far as I can tell.. all is good with config.

However, when I add the Meross as a Bridge to HK, it always says the Small Garage door is open and trying to open or close the Large Garage door controls the Small garage door.

I figure I have some configuration issue but I can't for the life of me figure out what I am doing wrong. :/

Any ideas would be appreciated when time permits.

Thank you!

[jasonmeurer]

Check out this post, the port mappings are off by 1.

Meross app Port 1/Garage Door 1 ----> HomeKit Smart Garage Door Opener
Meross app Port 2/Garage Door 2 ----> HomeKit Garage Door 1
Meross app Port 3/Garage Door 3 ----> HomeKit Garage Door 2

#546 (comment)

I ended up just renaming them in HB.