-
Notifications
You must be signed in to change notification settings - Fork 268
/
mz61581.cpp
123 lines (105 loc) · 4.65 KB
/
mz61581.cpp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
#include "config.h"
#ifdef MZ61581
#include "spi.h"
#include <memory.h>
#include <stdio.h>
void InitMZ61581()
{
// If a Reset pin is defined, toggle it briefly high->low->high to enable the device. Some devices do not have a reset pin, in which case compile with GPIO_TFT_RESET_PIN left undefined.
#if defined(GPIO_TFT_RESET_PIN) && GPIO_TFT_RESET_PIN >= 0
printf("Resetting display at reset GPIO pin %d\n", GPIO_TFT_RESET_PIN);
SET_GPIO_MODE(GPIO_TFT_RESET_PIN, 1);
SET_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
CLEAR_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
SET_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
#endif
// Do the initialization with a very low SPI bus speed, so that it will succeed even if the bus speed chosen by the user is too high.
spi->clk = 34;
__sync_synchronize();
BEGIN_SPI_COMMUNICATION();
{
// Reverse engineered with logic analyzer, not sure what these mean. If you have a data sheet for MZ61581, please send it my way.
SPI_TRANSFER(0xB0, 0x00);
SPI_TRANSFER(0xB3, 0x02, 0x00, 0x00, 0x00);
SPI_TRANSFER(0xC0, 0x13, 0x3B, 0x00, 0x02, 0x00, 0x01, 0x00, 0x43);
SPI_TRANSFER(0xC1, 0x08, 0x16, 0x08, 0x08);
SPI_TRANSFER(0xC4, 0x11, 0x07, 0x03, 0x03);
SPI_TRANSFER(0xC6, 0x00);
SPI_TRANSFER(0xC8, 0x03, 0x03, 0x13, 0x5C, 0x03, 0x07, 0x14, 0x08, 0x00, 0x21, 0x08, 0x14, 0x07, 0x53, 0x0C, 0x13, 0x03, 0x03, 0x21, 0x00);
SPI_TRANSFER(0x35, 0x00);
SPI_TRANSFER(0x44, 0x00, 0x01);
SPI_TRANSFER(0xD0, 0x07, 0x07, 0x1D, 0x03);
SPI_TRANSFER(0xD1, 0x03, 0x30, 0x10);
SPI_TRANSFER(0xD2, 0x03, 0x14, 0x04);
// The following coincide with e.g. ILI9341.
SPI_TRANSFER(0x3A/*COLMOD: Pixel Format Set*/, 0x55/*DPI=16bits/pixel,DBI=16bits/pixel*/);
#define MADCTL_BGR_PIXEL_ORDER (1<<3)
#define MADCTL_ROW_COLUMN_EXCHANGE (1<<5)
#define MADCTL_COLUMN_ADDRESS_ORDER_SWAP (1<<6)
#define MADCTL_ROW_ADDRESS_ORDER_SWAP (1<<7)
#define MADCTL_ROTATE_180_DEGREES (MADCTL_COLUMN_ADDRESS_ORDER_SWAP | MADCTL_ROW_ADDRESS_ORDER_SWAP)
uint8_t madctl = MADCTL_COLUMN_ADDRESS_ORDER_SWAP;
#ifndef DISPLAY_SWAP_BGR
madctl |= MADCTL_BGR_PIXEL_ORDER;
#endif
#if defined(DISPLAY_FLIP_ORIENTATION_IN_HARDWARE)
madctl |= MADCTL_ROW_COLUMN_EXCHANGE;
#endif
#ifdef DISPLAY_ROTATE_180_DEGREES
madctl ^= MADCTL_ROTATE_180_DEGREES;
#endif
SPI_TRANSFER(0x36/*MADCTL: Memory Access Control*/, madctl);
SPI_TRANSFER(0x11/*Sleep Out*/);
usleep(300 * 1000);
SPI_TRANSFER(0x29/*Display ON*/);
SPI_TRANSFER(0x2C);
// TONTEC_MZ61581 has backlight active when backlight GPIO is low, and at boot, it seems to be disabled, so always need to enable it.
#if defined(GPIO_TFT_BACKLIGHT) && (defined(BACKLIGHT_CONTROL) || defined(TONTEC_MZ61581))
printf("Setting TFT backlight on at pin %d\n", GPIO_TFT_BACKLIGHT);
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
CLEAR_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight on. MZ61581 backlight is on when the Backlight GPIO pin is 0.
#endif
ClearScreen();
}
#ifndef USE_DMA_TRANSFERS // For DMA transfers, keep SPI CS & TA active.
END_SPI_COMMUNICATION();
#endif
// And speed up to the desired operation speed finally after init is done.
usleep(10 * 1000); // Delay a bit before restoring CLK, or otherwise this has been observed to cause the display not init if done back to back after the clear operation above.
spi->clk = SPI_BUS_CLOCK_DIVISOR;
}
void TurnDisplayOff()
{
#if defined(GPIO_TFT_BACKLIGHT) && defined(BACKLIGHT_CONTROL)
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
SET_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight off.
#endif
#if 0
QUEUE_SPI_TRANSFER(0x28/*Display OFF*/);
QUEUE_SPI_TRANSFER(0x10/*Enter Sleep Mode*/);
usleep(120*1000); // Sleep off can be sent 120msecs after entering sleep mode the earliest, so synchronously sleep here for that duration to be safe.
#endif
// printf("Turned display OFF\n");
}
void TurnDisplayOn()
{
#if 0
QUEUE_SPI_TRANSFER(0x11/*Sleep Out*/);
usleep(120 * 1000);
QUEUE_SPI_TRANSFER(0x29/*Display ON*/);
#endif
#if defined(GPIO_TFT_BACKLIGHT) && defined(BACKLIGHT_CONTROL)
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
CLEAR_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight on.
#endif
// printf("Turned display ON\n");
}
void DeinitSPIDisplay()
{
ClearScreen();
SPI_TRANSFER(/*Display OFF*/0x28);
}
#endif