From 5e460143593f20fd6c369fab775f9a1cf5709232 Mon Sep 17 00:00:00 2001
From: haarp <781030+haarp@users.noreply.github.com>
Date: Tue, 30 Jul 2019 20:46:49 +0200
Subject: [PATCH 1/2] Make M109 S not wait for cooldown

fixes #1474
---
 Firmware/Marlin_main.cpp | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Firmware/Marlin_main.cpp b/Firmware/Marlin_main.cpp
index f3c722e52a..fd509cdc36 100644
--- a/Firmware/Marlin_main.cpp
+++ b/Firmware/Marlin_main.cpp
@@ -9722,6 +9722,7 @@ static void wait_for_heater(long codenum, uint8_t extruder) {
     cancel_heatup = false;
 	while ((!cancel_heatup) && ((residencyStart == -1) ||
 		(residencyStart >= 0 && (((unsigned int)(_millis() - residencyStart)) < (TEMP_RESIDENCY_TIME * 1000UL))))) {
+		if ((CooldownNoWait == true) && !target_direction) break;
 #else
 	while (target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder) && (CooldownNoWait == false))) {
 #endif //TEMP_RESIDENCY_TIME

From f23e5e57dc85cf53d81e87b2b291bffcffcaf7e1 Mon Sep 17 00:00:00 2001
From: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Date: Mon, 4 Jul 2022 18:55:14 +0200
Subject: [PATCH 2/2] Sync with upstream

Fix rebase issues
---
 Firmware/Marlin_main.cpp | 17 ++++++++++-------
 1 file changed, 10 insertions(+), 7 deletions(-)

diff --git a/Firmware/Marlin_main.cpp b/Firmware/Marlin_main.cpp
index fd509cdc36..65174d29a9 100644
--- a/Firmware/Marlin_main.cpp
+++ b/Firmware/Marlin_main.cpp
@@ -235,6 +235,7 @@ uint8_t newFanSpeed = 0;
   #endif
 
 static bool cancel_heatup = false;
+bool CooldownNoWait;
 
 int8_t busy_state = NOT_BUSY;
 static long prev_busy_signal_ms = -1;
@@ -6046,17 +6047,19 @@ SERIAL_PROTOCOLPGM("\n\n");
     */
     case 109:
     {
+      CooldownNoWait = false;
       LCD_MESSAGERPGM(_T(MSG_HEATING));
-	  heating_status = HeatingStatus::EXTRUDER_HEATING;
+      heating_status = HeatingStatus::EXTRUDER_HEATING;
       prusa_statistics(1);
 
 #ifdef AUTOTEMP
         autotemp_enabled=false;
-      #endif
+#endif
       if (code_seen('S')) {
-          setTargetHotend(code_value());
-            } else if (code_seen('R')) {
-                setTargetHotend(code_value());
+        setTargetHotend(code_value());
+        CooldownNoWait = true;
+      } else if (code_seen('R')) {
+        setTargetHotend(code_value());
       }
       #ifdef AUTOTEMP
         if (code_seen('S')) autotemp_min=code_value();
@@ -6078,7 +6081,7 @@ SERIAL_PROTOCOLPGM("\n\n");
       wait_for_heater(codenum, active_extruder); //loops until target temperature is reached
 
         LCD_MESSAGERPGM(_T(MSG_HEATING_COMPLETE));
-		heating_status = HeatingStatus::EXTRUDER_HEATING_COMPLETE;
+        heating_status = HeatingStatus::EXTRUDER_HEATING_COMPLETE;
         prusa_statistics(2);
         
         //starttime=_millis();
@@ -6102,7 +6105,7 @@ SERIAL_PROTOCOLPGM("\n\n");
     case 190: 
     #if defined(TEMP_BED_PIN) && TEMP_BED_PIN > -1
     {
-        bool CooldownNoWait = false;
+        CooldownNoWait = false;
         LCD_MESSAGERPGM(_T(MSG_BED_HEATING));
 		heating_status = HeatingStatus::BED_HEATING;
         prusa_statistics(1);