Q 2.4.6

Q2.4.4 to Q 2.4.6

• QServer - Resolved an issue in the data packet packing engine which affected header alignment in the stream. This issue was introduced in Q2.4.2.

Q2.3.7

Hotfix for Q2.3.x:

• Improved stability for SC4210 cards and added CAN42S support.

Q 2.4.4

Q2.4.3 to Q 2.4.4

• QServer - Resolved a phase delay issue affecting analog data channels.

Q 2.4.3

Q2.4.2 to Q 2.4.3

• QServer - Fixed a bug where the Tacho Generic Channel Header timestamp was incorrect.
• QServer - ALO Mirroring support added for DCH42 module.

Q 2.4.2

Q2.3.4 to Q 2.4.2

• New Features
  • QAcquire
    • Introduced minimum / maximum peak detection for analog channels, including a feature to hold the peaks.
    • Added the ability to set the recording duration in local storage before starting a recording.
    • Added a 'Reset' button to the main navigation. This will reset QServer and QAcquire settings to defaults.
    • Sidebar and fonts rework
      • Reworked all fonts to improve accessibility
      • Reworked the sidebar to represent the system as a logical mapping of the hardware
      • Removed the visual view and introduced a compact mode for the sidebar
      • Added an options menu to allow users to switch between list and compact views for the sidebar
    • Made changes to the sidebar channels and channel ID
      • Adjusted the display of the channel number in the list and included the QServer channel ID in the channel circle.
      • Added intermediate states to the local storage time string
      • Introduced icons for data status (local storage and streaming) for the sidebar channels in both list and visual mode.
  • QServer
    • Added an endpoint to get all the measurements recorded on local storage.
    • PTP network transport protocol can be configured using the Web Server.
• Bug fixes:
  • QDataManager
    • Resolved channel ID mismatches in local storage between QAcquire and QDataManager.
    • Local storage channel integrity field matches the data stream channel integrity field.
    • Fixed issue with plotting measurements less than 2 seconds.
    • Fixed local storage module ID assignment.
    • Fixed THM range scaling when exporting Local Storage measurements.
    • Fixed a bug where exported data is periodically zero.
  • QAcquire
    • Fixed a bug where the local storage start/stop button did not apply the settings correctly.
    • Fixed the bug where data state icons were disappearing
    • Fixed the bug where the slider component failed to update the value offset when switching between vertical split and normal mode
    • Local storage prevents the user from recording, displaying an error message if the disk is full.
    • Local storage settings are now disabled during recordings and removed arrow buttons for number inputs.
    • Fixed connection handling issues with QServer.
  • QServer
    • Fixed a bug where TEDS did not work on the MicroQ built-in ICP channels.
    • Local storage recording will return an error message if the disk space is full (disk reached the end of its reliable writing capacity).
    • PQ45 - Fixed a bug where the WiFi did not work when encryption is enabled.
    • WSB42Xx - Random periodic spikes/discharge distortion in constant current modes is now resolved.
    • CAN42S - Incorrect/inconsistent temperature readings fixed.
    • MicroQ - Fixed a bug where the XMC channels lose synchronisation with the system when using PTP. As a consequence, this bugfix causes QServer to reboot the MicroQ when enabling PTP or changing the Master Sampling Rate while PTP is enabled.

Q 2.3.4

Q2.3.3 to Q 2.3.4

• MicroQ - Fixed a bug where the XMC channels lose synchronisation with the system when using PTP. As a consequence, this bugfix causes QServer to reboot the MicroQ when enabling PTP or changing the Master Sampling Rate while PTP is enabled.

Q2.3.3

Q2.3.2 to Q 2.3.3

• PQ45 - Fixed a bug that caused the system to crash when an input to a CAN module is an unaligned size.

Q2.3.2

Q2.3.1 to Q 2.3.2

• MicroQ - Fixed a bug where the built in channels were slightly out of sync with the SC’s channels.

Q2.3.1

Q2.3.0 to Q2.3.1

• QServer - Fixed a bug where modules could miss a test restart after changing the sampling rate, causing a phase delay.

Q2.3.0

Q2.2.3 to Q2.3.0

• QServer - Added support for CHG42S9 module.
• QServer - Added support to "Mirror a Module" data stream using an ALO42S4.
• QAcquire - Updates for an improved user experience:
  • Local Storage:
    • The Settings section is initially hidden but can be revealed using the show/hide button.
    • The recording button will automatically apply system setting and show event notifications.
    • The current recording time, disk space and estimated time remaining are now available.
  • Navigation:
    • An enhanced navigation layout has been introduced to facilitate smoother action flow.
    • The save and restore are now part of the navigation as import / export.
  • System settings:
    • System settings and the channel sidebar have been merged.
    • The system node (QDevice controller) will be the first entry in the sidebar tree, selected by default.
    • Settings can be viewed/changed in the properties panel exactly the same as with the channels.
  • Embedded mode:
    • Home, Import, and Export buttons have been removed to align with the context of embedded mode.
    • Local Storage settings are always visible and adjusted the layout accordingly.
    • The recommended width for /&embedded is 265 pixels and with vertical split /&embedded&verticalSplit is 532 pixels.
    • QAcquire - The Temp / div settings have been adjusted to the highest level that the hardware can support.
• QAcquire - Implemented automatic range scaling for spectrum graphs.
• QDataManager - Added the new logo.
• QDataManager - Added Matlab and Wav exporters.
• PQ30 and PQ45 fan controller adjustments - fan speed set to "Maximum" at >= 75degC, will restore user fan setting at <= 70degC. System shuts down at >= 85degC.
• PQ45 fix to correctly display mainframe information in webserver.